FR Skates Jump Frames 244 mm – Inline Skate Frames for High Jump Competition
Built for jumping. Proven at the highest level. The FR Skates Jump Frames are high-performance inline skate frames developed specifically for competitive high jump and freestyle jump. Designed for skaters who want to push their limits, they combine a low-profile design, a rigid structure and a compact 244 mm wheelbase to support powerful take-offs and controlled landings.
Made from 6060 aluminium and weighing just 126 g per frame, including both axles but excluding spacers, the FR Jump Frames offer a lightweight and more affordable alternative to carbon frames for specialised jump skating.
If you are looking for FR Jump Frames, inline skate frames for high jump or dedicated freestyle jump competition equipment, this is one of the most specialised options to consider for your setup.
----
Specifically Designed for High Jump
In inline skate high jump, every detail of your setup matters. Frame geometry, rigidity, weight and wheel positioning all contribute to the skater’s feel during the approach, take-off and landing.
The FR Jump Frames have been developed specifically for competitive high jump. Rather than adapting a conventional urban frame for jumping, FR Skates has designed a dedicated platform to meet the demands of this discipline.
The result is a specialised frame for skaters who need a direct, responsive setup for training and competition.
----
Low-Profile Design for Take-Off and Landing Control
One of the key features of the FR Jump Frames is their low-profile design, which brings the skater closer to the ground and is intended to improve stability during take-off and landing.
The rigid aluminium structure helps reduce unwanted flex and supports efficient power transfer when pushing off. In a discipline where technique, timing and precision are essential, a frame designed around the specific demands of high jump can make a meaningful difference to the overall setup.
The compact geometry also helps keep the rear wheel overhang to a minimum, reducing the risk of catching the bar during a jump.
----
2x110 mm Wheel Setup and 244 mm Wheelbase
The FR Jump Frames use a 2x110 mm wheel configuration per skate with a total frame length of 244 mm. This combination pairs large-diameter wheels with a compact wheelbase to balance stability and manoeuvrability.
The 110 mm wheels provide a large rolling diameter, while the 244 mm frame length is designed for the specific movement requirements of competitive jumping. The reduced rear-wheel overhang is another important consideration when clearing the bar.
For athletes building a dedicated high-jump setup, this geometry offers a specialised alternative to conventional inline skate frames.
----
6060 Aluminium: Lightweight and Rigid
Manufactured from 6060 aluminium, the FR Jump Frames offer a lightweight option for skaters seeking dedicated jump equipment without the cost of a carbon frame.
Each frame weighs just 126 g, including two axles and excluding spacers. Keeping the frame lightweight is an important consideration for competition equipment, while the rigid structure is designed to provide a direct and controlled response.
FR Skates also reports that the Jump Frames have been used by winners at the 2026 World Championships, demonstrating their presence at the highest level of competition.
----
165 mm Mounting and Longitudinal Adjustment
The FR Jump Frames feature a 165 mm mounting standard and allow longitudinal adjustment depending on the compatible boot plate, including the manufacturer's specified 9-hole or 13-hole plate configurations.
Before purchasing, check that your boot and mounting plate are compatible. You should also verify the wheel, axle and spacer requirements for your intended setup.
----
Who Are the FR Jump Frames For?
These frames are designed primarily for:
-
Competitive inline high-jump athletes looking for equipment developed specifically for the discipline.
-
Freestyle jump skaters who want to optimise their setup for training and competition.
-
Skaters looking for specialised 244 mm frames with a 2x110 mm wheel configuration.
-
Athletes seeking a lightweight aluminium alternative to carbon jump frames.
They are specialist frames for jumping rather than a general-purpose choice for urban skating, slalom or conventional speed skating.
----
Technical Specifications
Brand: FR Skates
Model: FR Jump Frames
Manufacturer reference: FRFM-JMP210-244-BK
Product type: Inline skate frames
Recommended disciplines: Competitive high jump and freestyle jump
Material: 6060 aluminium
Colour: Black
Frame length: 244 mm
Wheel configuration: 2 x 110 mm per skate
Mounting standard: 165 mm
Longitudinal adjustment: Depending on compatible 9-hole or 13-hole plates
Weight: 126 g per frame, including 2 axles and excluding spacers
Wheels and spacers: Check package contents and required mounting components
----
Get Competition-Ready with FR Jump Frames
The FR Skates Jump Frames 244 mm are a specialist option for athletes serious about inline skate high jump. Their low-profile design, lightweight 6060 aluminium construction, compact wheelbase and 2x110 mm setup make them a compelling choice for building a dedicated competition skate.
Discover the FR Jump Frames at RollerStore and equip your skates with frames developed specifically for the demands of high-jump performance.
Español
