Swings MG Frame 3x110 + 1x100 – 325 mm Magnesium Speed Frame
The Swings MG Frame 3x110 + 1x100 is a high-performance racing frame developed for speed skating and demanding skaters looking for maximum efficiency, stiffness and weight reduction.
Manufactured from high-grade magnesium and precision CNC machined, it combines an extremely lightweight construction with the structural stiffness required for efficient power transfer.
With a 325 mm / 12.8" length, 3x110 mm + 1x100 mm wheel configuration and 195 mm mounting standard, this frame is designed for serious speed setups and skaters looking for a direct, precise and highly responsive skating experience.
At just 157 grams per frame, its magnesium construction is one of its major performance advantages over conventional aluminium frames.
CNC Magnesium – Maximum Stiffness with Minimum Weight
The defining feature of the MG Frame is its construction from high-grade magnesium, precision machined to create a rigid, lightweight and highly accurate structure.
At only 157 g, the reduction in frame weight is particularly valuable in speed skating, where every gram contributes to the overall mass that the skater has to move through every stride.
The objective, however, is not simply to reduce weight. The frame has been engineered to maintain high structural stiffness, allowing the power generated during each stride to be transferred efficiently through the boot, frame and wheels.
Low weight + high stiffness + efficient power transfer.
325 mm – Speed Skating Geometry
The frame measures 325 mm / 12.8 inches, providing a geometry specifically suited to high-level speed skating.
This length creates a stable platform for large-diameter wheels while maintaining efficient edge-to-edge transitions and predictable handling at high speed.
The geometry is designed to make the most of the skater's stride, helping transfer generated power into forward momentum with minimal energy loss.
3x110 mm + 1x100 mm Wheel Configuration
The MG Frame is designed for a specific 3x110 mm + 1x100 mm setup.
This configuration combines the rolling efficiency and speed retention of large wheels with a smaller front wheel to optimize the overall geometry and platform height.
Maximum configuration
3 x 110 mm + 1 x 100 mm
A dedicated setup for speed skating and racing performance.
195 mm Mounting Standard
The frame uses the 195 mm mounting standard, widely used for dedicated speed skating boots and race setups.
Correct frame positioning relative to the boot is essential for achieving efficient power transfer and allowing the skater to fine-tune the balance and handling characteristics of the skate.
Mounting standard: 195 mm
Direct Power Transfer
The MG Frame is engineered to minimize energy losses between the boot, frame and wheels.
Its high structural stiffness creates a stable platform for applying force during each stride, producing a direct and precise skating sensation.
In racing, where small efficiency gains can accumulate over an entire race, combining low weight with a rigid frame can make a meaningful difference to the overall setup.
Swings Speed Design – CNC Precision
The Swings Speed Frame concept focuses on high-performance manufacturing and precision engineering.
The frame combines precisely machined surfaces, optimized geometry and rigid side-wall construction to create a lightweight and efficient racing platform.
Its wider mounting deck is designed to improve the interface between boot and frame, helping maximize power transfer.
The direct flat side walls further support an efficient push, while the low-profile construction promotes quick and controlled edge-to-edge transitions.
Low Profile and Fast Response
The combination of a low profile and extremely lightweight construction contributes to a direct and responsive skating sensation.
The geometry is designed to promote efficient edge-to-edge movement, an important characteristic for speed skating where controlled lateral movement and powerful push efficiency are essential.
The Swings philosophy is to place stiffness where it is needed while optimizing the overall structure for efficient movement and power transmission.
Swings Speed Axles and Spacers
The overall Swings performance concept can be complemented by components designed with weight reduction in mind.
The Swings Speed Axles are manufactured from 7075 aluminium and CNC machined with an optimized central section to reduce weight while maintaining the strength required for racing applications.
The Swings Spacers are also made from 7075 aluminium and feature a 360° CNC-machined design. At approximately 1 g per spacer, they are engineered to minimize additional rotating and overall system weight.
Please note: these components are accessories and should be confirmed according to the specific product configuration supplied.
Designed for Serious Speed Skaters
The Swings MG Frame is not simply a lightweight frame.
It is designed for skaters who want to optimize every aspect of a high-performance speed setup:
Low weight → less mass to move
High stiffness → efficient power transfer
325 mm → stability and speed efficiency
3x110 + 1x100 → dedicated speed configuration
195 mm → speed skating mounting standard
CNC machining → precision manufacturing
A frame designed to take a dedicated speed skate setup to the next level.
Technical Specifications
- Brand: Swings
- Model: MG Frame
- Type: Speed Skating / Racing Frame
- Material: Magnesium
- Manufacturing: CNC precision machining
- Length: 325 mm / 12.8"
- Wheel configuration: 3 x 110 mm + 1 x 100 mm
- Maximum wheel diameter: 110 mm
- Mounting standard: 195 mm
- Weight: 157 g per frame
- Profile: Low profile
- Construction: High stiffness / lightweight
- Recommended use: Speed Skating / Inline Racing / Competition
Take Your Speed Setup to the Next Level
The Swings MG Frame 3x110 + 1x100 represents a highly advanced solution for skaters looking for an extremely lightweight, stiff and efficient speed skating frame.
Its CNC-machined magnesium construction brings the weight down to an impressive 157 grams per frame, while maintaining the stiffness required for demanding racing applications.
If you're building a 3x110 + 1x100 speed setup with 195 mm mounting and want to reduce weight without compromising stiffness and power transfer, the MG Frame is a genuine high-end racing option.
Español
